# Generated by PNCconf at Sat Feb 16 09:03:14 2013
# If you make changes to this file, they will be
# overwritten when you run PNCconf again

[EMC]
MACHINE = 1
DEBUG = 0

[DISPLAY]
DISPLAY = axis
POSITION_OFFSET = RELATIVE
POSITION_FEEDBACK = ACTUAL
MAX_FEED_OVERRIDE = 2.000000
MAX_SPINDLE_OVERRIDE = 1.000000
MIN_SPINDLE_OVERRIDE = 0.500000
INTRO_GRAPHIC = linuxcnc.gif
INTRO_TIME = 5
PROGRAM_PREFIX = /home/jirka/linuxcnc/nc_files
INCREMENTS = 5mm 1mm .5mm .1mm .05mm .01mm .005mm
POSITION_OFFSET = RELATIVE
POSITION_FEEDBACK = ACTUAL
DEFAULT_LINEAR_VELOCITY = 25.000000
MAX_LINEAR_VELOCITY = 33.333333
MIN_LINEAR_VELOCITY = 0.010000
DEFAULT_ANGULAR_VELOCITY = 0.250000
MAX_ANGULAR_VELOCITY = 1.000000
MIN_ANGULAR_VELOCITY = 0.010000
EDITOR = gedit
GEOMETRY = xyz

[FILTER]
PROGRAM_EXTENSION = .png,.gif,.jpg Greyscale Depth Image
PROGRAM_EXTENSION = .py Python Script
png = image-to-gcode
gif = image-to-gcode
jpg = image-to-gcode
py = python

[TASK]
TASK = milltask
CYCLE_TIME = 0.010

[RS274NGC]
PARAMETER_FILE = linuxcnc.var

[EMCMOT]
EMCMOT = motmod
COMM_TIMEOUT = 1.0
COMM_WAIT = 0.010
SERVO_PERIOD = 500000

[HOSTMOT2]
# **** This is for info only ****
# DRIVER0=hm2_pci
# BOARD0=5i20

[HAL]
HALUI = halui
HALFILE = 1.hal
HALFILE = custom.hal
POSTGUI_HALFILE = postgui_call_list.hal
SHUTDOWN = shutdown.hal

[HALUI]

[TRAJ]
AXES = 3
COORDINATES = X Y Z
LINEAR_UNITS = mm
ANGULAR_UNITS = degree
CYCLE_TIME = 0.010
DEFAULT_VELOCITY = 6.67
MAX_LINEAR_VELOCITY = 66.67

[EMCIO]
EMCIO = io
CYCLE_TIME = 0.100
TOOL_TABLE = tool.tbl

#********************
# Axis X
#********************
[AXIS_0]
TYPE = LINEAR
HOME = -50.0
FERROR = 0.005
MIN_FERROR = 0.0005
MAX_VELOCITY = 33.3333333333
MAX_ACCELERATION = 500.0
# these are in nanoseconds
DIRSETUP   = 1000
DIRHOLD    = 1000
STEPLEN    = 1000
STEPSPACE  = 1000
STEP_SCALE = 200.0
MIN_LIMIT = -73.0
MAX_LIMIT = 900.0
HOME_OFFSET = -50.0

#********************
# Axis Y
#********************
[AXIS_1]
TYPE = LINEAR
HOME = -136.0
FERROR = 0.005
MIN_FERROR = 0.0005
MAX_VELOCITY = 66.6666666667
MAX_ACCELERATION = 500.0
# these are in nanoseconds
DIRSETUP   = 1000
DIRHOLD    = 1000
STEPLEN    = 1000
STEPSPACE  = 1000
STEP_SCALE = 200.0
MIN_LIMIT = -150.0
MAX_LIMIT = 351.0
HOME_OFFSET = -136.0

#********************
# Axis Z
#********************
[AXIS_2]
TYPE = LINEAR
HOME = -10.0
FERROR = 0.005
MIN_FERROR = 0.0005
MAX_VELOCITY = 5.0
MAX_ACCELERATION = 400.0
# these are in nanoseconds
DIRSETUP   = 1000
DIRHOLD    = 1000
STEPLEN    = 1000
STEPSPACE  = 1000
STEP_SCALE = 504.0
MIN_LIMIT = -117.0
MAX_LIMIT = 26.0
HOME_OFFSET = -10.0

#********************
# Spindle 
#********************
[SPINDLE_9]